Home › Forums › Help and Support › Where is the log? error mcv…small
- This topic has 12 replies, 2 voices, and was last updated 7 years, 1 month ago by lesporty.
-
AuthorPosts
-
2017-03-07 at 6:31 #6125
Hi,
I am using Huey to calibrate an Acer LED monitor. Have the mcv…small error. Tried a couple of times, same problem.
May I know where is the log kept so that I can upload to seek assistance?
Thanks.
2017-03-09 at 11:23 #6141Hi,
please see the documentation.
2017-03-14 at 6:32 #6256Hey, thanks.
Managed to grab the log and this is what it says. Can anyone help suggest a solution? Thanks.
There are 3 files but I believed these 2 are the relevant ones. Thanks again.
Attachments:
You must be logged in to view attached files.2017-03-15 at 11:05 #6268What instrument is this? The readings are totally out of whack, suggesting that the instrument may be broken in some form:
Red = XYZ 52.347 12.584 0.676
Green = XYZ 55.456 49.357 7.007
Blue = XYZ 19.541 5.252 106.052
White = XYZ 127.760 67.257 114.871Had to scale brightness from 67.236118 to -0.000000 to fit within gamut
2017-03-16 at 2:22 #6273Oh??
I am using a Huey Gretamacbeth calibrator on an Acer G247HYL LED monitor.
2017-03-16 at 11:47 #6276Try if it works with the vendor software. How old is the Huey?
2017-03-17 at 12:27 #6288Hi Florian,
In light of your comment that the sensor may not be working, I have re-calibrated the led again using the vendor’s Huey calibration software (for gretaMacbeth). It works fine- the sensor is flashing, measuring and adjusting throught the process.
Then I tried calibrating with Displaycal. The software recognise the instrument automatically. When I click “calibrate & profile” and then “start measurement” within the measurement area box, the sensor flashes and then the “interactive display adjustment” windows appear. From then on- be it during “start measurement” or “continue to calibrate” after that and the software going through the patches etc, the sensor never lighted/flashes at all.
I guess it is not receiving instructions from the software to start measuring and calibrating? That’s why the error?
Seems to only work with vendor software- but it should also work with this calibrating software right, being one of the listed sensors?
Thanks.
2017-03-17 at 15:42 #6289It works fine- the sensor is flashing, measuring and adjusting throught the process.
The question is if a usable profile comes out of it – can you attach it?
When I click “calibrate & profile” and then “start measurement” within the measurement area box, the sensor flashes and then the “interactive display adjustment” windows appear. From then on- be it during “start measurement” or “continue to calibrate” after that and the software going through the patches etc, the sensor never lighted/flashes at all.
It’s not supposed to when using Argyll (the flashing LEDs are just a gimmick).
2017-03-17 at 16:58 #6290Certainly- I believed this is the profile file.
Thanks.
Attachments:
You must be logged in to view attached files.2017-03-17 at 17:18 #6292Certainly- I believed this is the profile file.
That’s not the one – this comes from the MS Windows calibration wizard and is not based on measurements.
2017-03-17 at 17:22 #6293Thanks= then it must be this one.
Attachments:
You must be logged in to view attached files.2017-03-17 at 17:37 #6295Ok. Looking at that profile, I think it’s safe to say that the huey has indeed expired.
Attached are the calibration curves from the profile as well as the gamut outline.
Attachments:
You must be logged in to view attached files.2017-03-18 at 8:27 #6304ok. Thanks very much.
I will look for another sensor and try again.
Thanks again for your help.
-
AuthorPosts