LG C8 Lut

Home Forums General Discussion LG C8 Lut

Viewing 15 posts - 16 through 30 (of 279 total)
  • Author
    Posts
  • #17548

    Abdessamad Elkanfoud
    Participant
    • Offline

    Everything is ok with the new build.

    Thank you very much & hope you can add 1dlut support in the future.

    #17561

    tonybcc
    Participant
    • Offline

    Would you mind sharing your settings for calibration and 3dlut ? It would be very helpful.

    thank you

    #17562

    Abdessamad Elkanfoud
    Participant
    • Offline

    here

    Attachments:
    You must be logged in to view attached files.
    #17570

    tonybcc
    Participant
    • Offline

    Thank you for sharing your settings. Where did you get c8 correction from?

    You are using madvr. I want to use raspberry pi as pattern generator but it doesn’t work or I don’t know how to make it work .

    #17581

    tonybcc
    Participant
    • Offline

    @Florian would you consider adding  raspberry pi as pattern generator? I heard it is bit accurate and relatively cheap that would be icing on the cake ????.

    regards.

    #17582

    tonybcc
    Participant
    • Offline

    Or maybe it is other way to control it. I downloaded  pgenerator from Light… and it works with Calman HCFR and LightSpace. Please think about it.

    #17586

    Abdessamad Elkanfoud
    Participant
    • Offline

    Thank you for sharing your settings. Where did you get c8 correction from?

    It’s basically an edr correction file converted to ccss, the edr file was made by lightillusion, Flanders Scientific and X-Rite.

    Attachments:
    You must be logged in to view attached files.
    #17588

    Florian Höch
    Administrator
    • Offline

    Note though that this EDR file has been created with the TV in Rec. 709 gamut emulation mode. DisplayCAL comes with a CCSS (LG OLED 6 series) that was created with the TV in native (roughly P3) gamut mode.

    #17589

    tonybcc
    Participant
    • Offline

    Thank you . As for raspberry, would you know how to control it?

    #17637

    Florian Höch
    Administrator
    • Offline

    It is not currently supported.

    #17663

    tonybcc
    Participant
    • Offline

    @abdessamad

    are you happy with results of 3dlut ? Can you share calibration settings as well?


    @Florian

    will you consider adding raspberry as controller? Or add something like external ip adress window so we can input raspberry ip  adress

    regards.

    #17665

    Abdessamad Elkanfoud
    Participant
    • Offline

    @abdessamad

    are you happy with results of 3dlut ? Can you share calibration settings as well?

     

    Yes, i’m very happy with the results, the best i’ve ever had.

    1- Using DCC Reset 3DLUT only.

    2- Set  oled light to your target nits (26 for my panel to get arround 102nits)

    3- Brightness Calibration (51 is the right setting for my panel)

    4- 2p WB High calibration

    P.S: I’ve skipped 1dlut calibration because it needs brightness set to bypass value (50) to work correctly, and 50 for my panel is not right and cause a bit of shadow details crash.

    #17666

    Abdessamad Elkanfoud
    Participant
    • Offline

    Forgot to mention, i’ve used 2.2 gamma tv preset as it’s the native tv response, then targeted 2.4 for the 3dlut.

    #17883

    stama
    Participant
    • Offline

    @tonybcc , if you are calibrating for PC use, use the PC as the pattern generator. Measure what you are trying to correct, not something else.


    @abdessamad
    , is anyone allowed to use DeviceControl to upload 3D LUTs to the TV, or do you need a LightSpace license for that?

    #17884

    Abdessamad Elkanfoud
    Participant
    • Offline

    Yes, you need LS licence to get LG Templates cloud access for DCC.

Viewing 15 posts - 16 through 30 (of 279 total)

You must be logged in to reply to this topic.

Log in or Register

Display Calibration and Characterization powered by ArgyllCMS